What a lacquered wood jewellery set box is — and what it has to do
A set box presents a matching ring, necklace and earrings together in one opening, with a compartment shaped for each. It suits bridal, gifting and signature collections where the pieces are sold as one story.
A lacquered double-door set box is the most formal presentation we make — side-hinged doors, a lined vertical board, and a shell finished in as many coats as a piano.
How a lacquered wood jewellery set box is built inside
The classic set box is a double-door format: two doors open left and right on side hinges, revealing a single vertical display board. The board is worked from the top down — a hook or clip for the necklace, pierced holes for the earrings in the middle, and a ring slot at the base — so the whole set reads as one composed picture. A simpler flat set box uses a base pad with a shaped compartment for each piece.
Fit. Each position uses the same rule as its single box — 2–4 mm ring slot, 0.8 mm pierced earring holes, a hook sized to the bail — set out on one board so the pieces do not overlap when the doors close.
In lacquered wood. Inside a lacquered shell the insert sits in a routed recess rather than against a wrapped wall, so the insert is cut to the recess and the lining is turned into the gap — the lacquered rim stays clean and the pad cannot lift. Shell walls are thicker than a moulded box, which is why a wood box feels heavier for the same internal size.
Formats we make: double-door display board · flat compartment set box · bridal parure box · two-piece (pendant and earrings) set box.
Why lacquered wood for jewellery set boxes
A lacquered wood box is a keepsake in its own right. The shell is built up in layers and hand-sprayed to a deep, even shine, giving a weight and quality that customers keep long after the sale.
Because a wooden shell is cut rather than moulded, the external dimensions are free — this is the route we recommend when a piece needs a size that no ready tooling matches. Lacquer is applied in several coats with sanding between, so the finish depth and gloss level (high gloss, satin or matte) are part of the specification.
Any lacquer colour can be matched, with piano black, deep burgundy and warm walnut the most requested; interiors are lined in velvet or suede to protect the piece against the hard shell.
It suits higher-value pieces, collectors, watch brands and gifting where the box is expected to be kept and reused.
Specification at a glance
| Piece held | Matching set |
|---|---|
| Insert | A single vertical display board (necklace hook, earring holes, ring slot) or a multi-compartment flat pad |
| Fit detail | Each position uses the same rule as its single box — 2–4 mm ring slot, 0.8 mm pierced earring holes, a hook sized to the bail — set out on one board so the pieces do not overlap when the doors close. |
| Typical external size | Double-door set boxes are typically 120–160 mm wide and 150–200 mm tall; flat set boxes run 160–220 mm by 120–160 mm. |
| Formats | double-door display board · flat compartment set box · bridal parure box · two-piece (pendant and earrings) set box |
| Exterior | Lacquered Wood — piano black, burgundy, walnut, ivory, navy, forest green |
| Hand feel | Heavy, lacquered, keepsake — the box stays on the dressing table |
| Insert construction | Lined pads set into a routed recess |
| Interior lining | Velvet, microfibre suede or satin, in a matching or contrast colour |
| Logo | On lacquer the logo is normally printed or foil-stamped on the lid, or set as a metal plate; a debossed logo is also possible under the lacquer for a subtle 'in the surface' look. |
| Closure | Hinged lid with a snap or magnetic catch; ribbon or clasp on travel formats |
| Shell route | Ready tooling library (no mould charge) where a standard size fits; fully custom dimensions on a wooden shell where it does not |
| Sample | A physical pre-production sample is made and approved before any bulk run |
| Quantity & lead time | Quoted per project — structure, materials and any tooling decide both; tell us the quantity you have in mind |
Two ways to get the size you need
Every box starts with the piece, and the piece decides the shell route:
- Ready tooling library. We hold a range of existing moulded shells in the common jewellery-box sizes. Where one of these fits your piece, there is no mould charge and the box is faster to produce — you choose the finish, lining and logo on a proven shell.
- Fully custom dimensions. Where no standard shell suits — an unusual matching set, a signature proportion, a matching family of sizes — we build the box on a wooden shell cut to your dimensions and finished in lacquer or wrapped in your chosen material.
We will tell you which route fits your brief before quoting, so there are no surprises on tooling or timing.
What we check on every lacquered wood jewellery set box
Before a sample is sent, and again on every bulk run, each lacquered wood jewellery set box is checked against the same points — the insert is lined pads set into a routed recess, so the fit checks below are read against that construction:
- doors open evenly and the board sits vertical
- necklace hangs clear of the earrings; earrings clear the ring
- no piece touches the doors when closed
- board is fixed rigidly — it must not flex when the set is fitted
- the lacquer is even across all faces with no dust or orange peel at the corners
- lid and base outlines match exactly when closed — same footprint, same corner radius
- insert fills the cavity with no gap to the wall; walls are an even thickness
- lacquered wood panels have continuous grain or nap with straight, even seams
The most common faults we see in jewellery set boxes bought elsewhere are positions set too close so the chain lies over the earrings, doors that do not meet flush, and a board that leans when loaded. Each of those is a specification decision, and we make it with you before the sample.
Made to your brand
Your size, your lining, your colour, your logo. On lacquer the logo is normally printed or foil-stamped on the lid, or set as a metal plate; a debossed logo is also possible under the lacquer for a subtle 'in the surface' look. Lacquer is durable but shows fingerprints on high gloss — a satin finish is the practical choice for display boxes that are handled daily.
You approve a physical sample before bulk, and the bulk order is held to the sample you approved — the same lacquered wood, the same insert, the same logo position.
How ordering works
Send us the matching set dimensions (or the piece itself), the quantity you have in mind, your logo artwork and any colour references. We confirm the shell route and the insert, quote one clear all-in price, and make a pre-production sample for you to approve. Production follows the approved sample. Quantities and lead times are agreed per project rather than fixed, because structure, materials and any tooling decide both.
Why Chung Ngai
Chung Ngai is a manufacturer and supplier of jewellery and watch packaging, Hong Kong owned and managed since 1971. We build and check boxes by hand, quote one transparent price, and hold every bulk run to the approved sample. For lacquered wood jewellery set boxes made to your brand, that consistency is what keeps jewellers re-ordering.