What a rigid board earring box is — and what it has to do
An earring box holds a pair neatly with slots, a flap or a foam pad, so studs and drops stay together and face forward. Small and precise, it is one of the most-used boxes in any jewellery range.
Rigid earring boxes are the workhorse of e-commerce jewellery: a small magnetic-closure box, printed wrap, and a pierced pad — light enough to post in a padded envelope.
How a rigid board earring box is built inside
The base pad carries two pin holes or two short slits set a fixed distance apart; the earring posts push through and the pair stands upright, side by side. For drops and hoops a small covered flap replaces the pad — the posts go through the flap and the drops hang free below it, so nothing is crushed when the lid closes.
Fit. Pin holes are pierced, not cut, so the pad grips a standard 0.8 mm post; the two holes sit 15–20 mm apart so the pair reads as a pair without touching.
In rigid board. In a rigid box the insert is glued to the greyboard base and the wrap paper is turned over the top edge, so the insert height is set to finish a few millimetres below the rim and the lid pad closes the gap. Because the board is wrapped, corner build-up is controlled by the paper weight — a heavier art paper needs a mitred corner to sit flat.
Formats we make: stud box with a pierced pad · slit pad for lever-backs · flap box for drops and hoops · deep box for chandeliers.
Why rigid board for earring boxes
A rigid (set-up) board box gives a premium, structured feel at a lighter weight and cost than wood, which makes it the practical choice for retail volume and shipping.
A rigid box is a greyboard shell wrapped in your chosen paper or fabric; board weight, wrap paper and closure decide how it feels. We use a heavier board than folding cartons so the box does not flex, and a magnetic or ribbon closure so it opens with a deliberate action rather than a flap.
The wrap paper sets the colour and texture: textured art papers, soft-touch laminates and metallic papers are all standard, and the same paper can be used across a whole retail range for consistency.
It suits e-commerce brands, multi-store retailers and seasonal or gifting ranges where quantity and shipping cost matter.
Specification at a glance
| Piece held | Pair of earrings |
|---|---|
| Insert | A twin-hole or twin-slit pad, or a covered flap for drops and hoops |
| Fit detail | Pin holes are pierced, not cut, so the pad grips a standard 0.8 mm post; the two holes sit 15–20 mm apart so the pair reads as a pair without touching. |
| Typical external size | Most earring boxes are 55–75 mm square and 30–40 mm deep; drop-earring flap boxes go deeper — 45–55 mm — to give the drops room to hang. |
| Formats | stud box with a pierced pad · slit pad for lever-backs · flap box for drops and hoops · deep box for chandeliers |
| Exterior | Rigid Board — any Pantone reference on the wrap paper; soft-touch black, kraft, ivory and blush are the most common |
| Hand feel | Structured, light, printable — premium at shipping weight |
| Insert construction | A lined foam insert glued to the board base |
| Interior lining | Velvet, microfibre suede or satin, in a matching or contrast colour |
| Logo | Rigid board takes any print method — foil stamping, spot UV, embossing or full-colour print on the wrap — so it is the most flexible surface for brand artwork, patterns and colour blocking. |
| Closure | Hinged lid with a snap or magnetic catch; ribbon or clasp on travel formats |
| Shell route | Ready tooling library (no mould charge) where a standard size fits; fully custom dimensions on a wooden shell where it does not |
| Sample | A physical pre-production sample is made and approved before any bulk run |
| Quantity & lead time | Quoted per project — structure, materials and any tooling decide both; tell us the quantity you have in mind |
Two ways to get the size you need
Every box starts with the piece, and the piece decides the shell route:
- Ready tooling library. We hold a range of existing moulded shells in the common jewellery-box sizes. Where one of these fits your piece, there is no mould charge and the box is faster to produce — you choose the finish, lining and logo on a proven shell.
- Fully custom dimensions. Where no standard shell suits — an unusual pair of earrings, a signature proportion, a matching family of sizes — we build the box on a wooden shell cut to your dimensions and finished in lacquer or wrapped in your chosen material.
We will tell you which route fits your brief before quoting, so there are no surprises on tooling or timing.
What we check on every rigid board earring box
Before a sample is sent, and again on every bulk run, each rigid board earring box is checked against the same points — the insert is a lined foam insert glued to the board base, so the fit checks below are read against that construction:
- both earrings stand upright and face forward at the same angle
- posts are gripped by the pad and do not fall out when the box is tilted
- drops hang free of the base when the lid is closed
- the pair is centred in the box, not pushed to one side
- the wrap paper has no bubbles, tears or paper build-up at the corners
- lid and base outlines match exactly when closed — same footprint, same corner radius
- insert fills the cavity with no gap to the wall; walls are an even thickness
- rigid board panels have continuous grain or nap with straight, even seams
The most common faults we see in earring boxes bought elsewhere are holes punched too large for fine posts, a pad too thin to grip, and a flap box too shallow so the drops touch the base. Each of those is a specification decision, and we make it with you before the sample.
Made to your brand
Your size, your lining, your colour, your logo. Rigid board takes any print method — foil stamping, spot UV, embossing or full-colour print on the wrap — so it is the most flexible surface for brand artwork, patterns and colour blocking. Rigid boxes stack flat-sided and are the most efficient to ship and store, which is why e-commerce brands packing many orders default to them.
You approve a physical sample before bulk, and the bulk order is held to the sample you approved — the same rigid board, the same insert, the same logo position.
How ordering works
Send us the pair of earrings dimensions (or the piece itself), the quantity you have in mind, your logo artwork and any colour references. We confirm the shell route and the insert, quote one clear all-in price, and make a pre-production sample for you to approve. Production follows the approved sample. Quantities and lead times are agreed per project rather than fixed, because structure, materials and any tooling decide both.
Why Chung Ngai
Chung Ngai is a manufacturer and supplier of jewellery and watch packaging, Hong Kong owned and managed since 1971. We build and check boxes by hand, quote one transparent price, and hold every bulk run to the approved sample. For rigid board earring boxes made to your brand, that consistency is what keeps jewellers re-ordering.